Homemade tents for winter fishing. Homemade tents for fishing

If a folded metal fan is bent in the middle by 45 degrees and then unfolded, you will get a miniature tent. A homemade winter tent was made on this principle. The tent is quadrangular, but there are five poles - the fifth pole when “closing” the tent is superimposed on the fourth. It is convenient to transport it in a case 1 meter high and 15 centimeters in diameter. Total weight 3 kilograms. Disassembly and assembly takes no more than a minute.

Homemade tent diagram

Fig. 1 Homemade tent unfolded: 1 - stand, rigidly fixed; 2, 3, 4, 5 - movable racks

Fig.2 Homemade tent folded for moving to a new place

Fig.3 Homemade tent in transport position

Fig.4 The top of the awning, covered with oilcloth or tarpaulin and pressed with a wing bolt.

The frame of a homemade winter tent is made of aluminum ski poles. On the top plate (duralumin 3 millimeters thick), let’s call it a “circle,” three M6 bolts with solid threads are rigidly installed from bottom to top, which are the axes of rotation of racks 2, 3, 4 and 5.

Rack 1 is fixed rigidly. Each bolt on top of the plate is tightly tightened with a nut. The middle bolt rises above the two side bolts in such a way that posts 4 and 5 pass freely over them.

In the front part of the circle, a plate with bends for the hooks of posts 2 and 3 is rigidly fixed at the bottom; hooks secure the poles when the tent is fully opened. Racks 4 and 5 can be in an intermediate position - next to racks 2 and 3 or connected to each other.

All racks, except the fifth one, have spacers that keep them from folding inward. When unfolding a homemade tent, you need to press each one with your hand, and when folding, pull it towards you.

For greater lateral stability of a homemade tent, posts 1, 2 and 3 are connected to each other by crosses made of narrow braid. The crosspieces also protect the plastic film from being “pushed” by the wind into the tent.

The awning is made of polyethylene film. Ribbons are sewn onto the awning from the outside and inside against each post using a stitch with a large pitch. To attach the awning to the frame, ties are sewn to the awning against each break in the posts and the bottom of the posts. At the top of the awning, the film is carefully collected and covered with a cap made of oilcloth or tarpaulin and not tightly clamped using a wing bolt.

It is advisable to fold the tent in the direction of the wind so that the awning moves away from the poles. If this is not done, the tent may be cut by the struts. When there is no wind, you just need to straighten the awning with your hand, then in one motion fold the poles, straighten the film and put it in the cover the same way you put an umbrella.

All parts and components of the tent structure are easy to manufacture, and there is no need to describe the technology in detail. The connections are like a camp cot, but with bolts and nuts. If you replace them with rivets, the tent will become even lighter.

During winter fishing, the angler needs to protect himself from many weather conditions that are acceptable in winter time and for this, it is very well suited.

In addition, it increases the time the fisherman stays in cold weather. If you use heating devices in the tent, then the air in it can be heated to 20 degrees and you can freely stay in it without outer clothing.

Types of winter fishing tents

Winter tents are divided into types, which determine their design, installation and assembly.

Umbrella. This type is considered the simplest in its design. It has an umbrella design, making it easy to install and assemble. To make the frame, duralumin rods are used, which increase the reliability and strength of the tent. The awning can be made of synthetic fabrics or a combination with tarpaulin.
Machine. The scheme of their construction is that a tent is sewn to the frame. When assembling, it is enough to twist it into a circle, and it unfolds instantly due to the action of the frame, which works like a spring. Such tents are becoming increasingly popular among fishermen because they have a low price and light weight. But along with this, it has many disadvantages: poor resistance to wind, the frame easily breaks if the tent is not set up correctly.
Frame. Its design resembles the usual summer version. It folds out of several folding arches and an awning. She sorts it out in about 10 minutes, or even more. The tent is not particularly reliable. It is rare for fishermen to purchase this type of winter tent.

What requirements must a homemade tent for winter fishing meet?

Should create the most favorable conditions on cold, windy, winter days. In addition, it should serve as a place where you can cook a meal, drink hot tea and just warm up.

Nowadays the market is full of all possible types of tents, but it is still nice to make one yourself. If you are sewing a tent yourself, you must meet certain requirements:

It should be light and compact.
Since it is portable, the tent must be mobile.
Select fabrics that are dense.
It should be assembled and unpacked conveniently and quickly.
When making it, it is better to give preference to stronger and more reliable materials. The heat in the middle of the structure should be maintained for as long as possible.

What materials and tools will you need?

A very common, homemade one is a design based on. It can be bought at any store that specializes in selling fishing gear. In addition, you will also need some accessories:

Skis, two pairs (children's and school version)
Tubes, you can use ski poles.
An old folding bed.
Thick fabric, tarpaulin is best.

At first glance, it is not entirely clear what this design will look like. But, in practice, its effectiveness and ease of use have been proven. After completing the design, you should end up with a box that can be transported using skis. In addition, it is easy to assemble and move even on ice.

Drawings of a homemade winter tent

As you can see from the diagram, the tent is mounted on skis and this makes it easier to secure it on the ice. After all, for fastening conventional winter tents it takes a lot of time and effort. And with such a design, the fisherman can move around the reservoir many times. Wherever a new hole is made, the angler drags it towards him and, having climbed inside, is ready for fishing in warmth and comfort.

Note! To reduce windage and make it easier to drag the tent in strong winds, you need to remove the awning from the tent. If you don’t do this, it will simply be difficult to drag it.

Step-by-step instruction

This design is very old, but very reliable. More than one generation of fishermen have tested it in practice.

How to make a tent with your own hands photo and pattern

Ski poles will serve as a frame, where they are installed vertically. Horizontal tubes should be an order of magnitude thinner. The upper nodes must be made in the form of a triple connecting adapter and its end is made like a cylinder. It is worth noting that the diameters of the cylinder and the tubes with which they are connected must match.
Next, the tubes are secured in a vertical position to the skis. A T-shaped tongue is inserted into a metal plate attached to the ski, which is located at the lower end of the tube. After this, the tube is rotated 90 degrees.
Two tubes taken from a folding bed serve to connect the frame to the box. The end of the connecting product is secured to the end of the bent tube. The latch is installed at the other end of the tube.
Eyelets made from copper strip will serve to connect the box with the tubes.
At the end of all the work, all that remains is to pull the awning. Metal plates with slots are installed in its lower part. You need to insert staples into these slots, which are driven into the side ends of the skis. The connections are secured with laces. In order for the structure to remain stable on a frozen body of water, it must be equipped with two anchors.

Homemade tent pegs and screws

In order to make pegs that will be used for a winter tent, you need to take long and strong screws. The peg has a hook-shaped top. This process is performed using pliers. Screws are made of metal tubes that have threads. If you don’t have one, then self-tapping screws will do just fine.

How to sew a tent with your own hands in the form of a house

We can consider another very popular look tents that are made in the form of a house. For self-made You will need this tent:

Fabric that does not get wet - 14 sq. m.
Metal washers – diameter 1.5 mm (up to 20 pcs.)
Braided rope – 15 meters.
Not a wide tape - 9 meters.
Rubberized fabric for bedding - 6 meters.

Having prepared all the materials, you can proceed to making a tent that can accommodate one or two people. To begin, cut out 2 pieces of fabric of the same size - 1.8 by 0.9 meters. A marking of 65 centimeters is made along the long side, and the same operation is performed on the other side. The fabric is cut at the connection points. This creates the entrance and back wall of the tent.

In order not to envy your fellow fishermen who are hiding in reliable shelters from the severe frost and the prickly, evil wind, make a homemade tent for winter fishing. Do some unusual work with your own hands. Then staying on the pond during the cold season will become even more comfortable and memorable.

Let's figure out what the tents offered by various companies for fishermen are. There are many interesting solutions to such a problem as shelter from bad weather on a winter pond. However, all design options for such devices can be reduced to three main groups:

Frame device. A tent consists of a collapsible frame, usually rectangular or prismatic in shape. A canvas cover is placed on the frame.
Umbrella device. The shelter frame consists of an easily assembled structure, created according to the principle of an umbrella. A canvas cover is also placed on top.
Automatic device. Very popular recently are designs with an automatically folding frame with already stretched water-repellent fabric. What is attractive about such devices is the speed and ease of setting up a tent.

If the prices for factory-made products are steep, think about a DIY project. With your own hands you can make a device that will satisfy all the personal wishes and individual characteristics of the fisherman. After all, all people different heights, weight and constitution. Some people love space, some love comfort and convenience, and some love simplicity and reliability. There may be a need to take into account the characteristics of local reservoirs and weather conditions.

The main thing for a winter shelter is reliability, ease of assembly and the ability to quickly move. Staying on a pond in winter requires significant and frequent changes of places fishing, so think about these important requirements for your future shelter.

It is important to carefully and correctly select materials for manufacturing. The fabric for covering should be light, waterproof, but at the same time breathable and retain heat well. Pay attention to thermal insulation Special attention. The main purpose of such a device is to keep warm.

For the frame, choose a light and durable material. An old cot made of aluminum pipes, ski poles or durable and lightweight tubes are an excellent option for making a winter tent frame with your own hands.

Think in advance about how you will assemble and move your creation, and how to heat it, if necessary. Before you start manufacturing, it is important to calculate the costs and think carefully about all the tasks to be solved.

The procedure for manufacturing the structure

So, the question arose of how to make a tent with your own hands, where to start, what is the manufacturing sequence. Here is a simple diagram of the sequence of steps of what is needed, so that you end up with the desired shelter:

A self-made tent will help you not to pay attention to the weather. No frost or wind will stop you from enjoying what you love.

You can buy a tent for winter fishing. They are different: large, small, medium; quite cheap and quite expensive. In any case, you can choose according to your budget and needs, buy it and not bother - that’s my opinion. But, there are people with obvious “creative incontinence” and too even hands, growing from exactly that place. 😀 This article is for them - how to make your own tent for winter fishing.

So, why is it needed? For protection from wind and snowfall. Let's consider several options for making your own tent for fishing in winter. As usual, there is a simple way and a more complex, thorough one, and also a very thorough and very labor-intensive one. I will briefly describe all three.

. Well, this is the most conventional and easiest to make shelter from the snow and, to some extent, from the wind.

It's not even a tent, but rather a cape. Our task is to make a dome from thick polyethylene film. The support of the tent will be an ice screw. To do this, extend the drill to the maximum and screw it into the ice at an angle, as can be seen from the figure. Polyethylene can be cut in the form of an isosceles right triangle, so that when folded in half, you naturally get a rectangular isosceles triangle. If you forgot geometry or didn’t understand anything, here is the diagram.

Accordingly, we sew on a zipper that can be used to close it. We make holes in the grommets along the perimeter of the bell. Through these holes we will attach the cape to the ice using steel pins or nails.

Tent dome made of polyethylene - not The best decision, in terms of strength. It is quite difficult to sew a zipper well without tearing the film. But, on the other hand, the film is transparent and everything around is visible. So, you can make a dome from fabric (light, translucent or denser). You can make a dome using a more advanced pattern. This is already a transition to a more complex winter tent design. Here, an ice screw won’t work as a support. At a minimum, you need a central support, higher. It can be made foldable by holding the sections together with tubes, like the old bamboo fishing rods. One end is sharp to pierce the ice. We pull the canopy onto such a central support and tighten the edges by driving pins into the ice through the holes (or using guy ropes sewn to the tent canopy).

Even more complex structures, as in the figure, require more than one support. In addition to the central one, 4 or more auxiliary supports are required on the sides. This way you can make a fairly large tent. Of course, the larger the tent, the more folding poles, the heavier and bulkier the tent will be when folded...

And, the most outdated, time-consuming and complex option make a tent for winter fishing– make a collapsible rigid frame from aluminum tubes. And a dome made of thin fabric is pulled over the assembled frame. There are many design options! I think if you have reached the point in life where you want to make this kind of tent yourself, then you will design it, construct it yourself to make it even more interesting 😉

I repeat. Personally, I think that with the current abundance of winter tents on sale, and their moderate cost, doing it yourself is a dubious idea. But perhaps there are fans of various homemade products and they will decide make a tent for winter fishing with your own hands. I hope these brave people will find some useful ideas in the proposed material. 😉

Awnings according to their purpose are divided into:

intended for parking;
for swimming;
for transportation.

Parking

Protect the boat from external factors when laying up. The awning completely covers the boat, turning it into a vessel, which, for example, allows necessary repair work to be carried out under the roof.

the motor is tightly closed and protected from water ingress;
fastening is done with cords threaded into special rings of the awning design fittings;
The simple design ensures fast, reliable and durable installation.

Swim awnings

Nasal. Performs the function of protection against splashing water. Installed on the bow of the boat. Options:
- with viewing glass;
- without viewing glass.
- Characteristics:
- primary colors of green and gray;
- small volume and weight;
- easy installation;
- aerodynamic shape that helps maintain initial speed and stability.
Running gear. The awning reliably protects the fisherman from exposure to the sun, wind and water. Consists of front, side and rear structural elements. There are 2 types of awnings by design:
- with one-piece elements;
- with connected elements.
Transformer. This type is the best option for protection and convenience. The unique name was obtained due to the presence of six transformation positions, through which ventilation is ensured, as well as fishing on inclement days. Made in a tent style, with easy installation and use, taking into account the complete cover of the boat.
Frame. These awnings are also called “roof awnings”. Provide protection for the fisherman and his accessories from excessive exposure to the sun's rays and precipitation. Quite easy to install and use awning. The presence of high strength and long-term use are its characteristic distinguishing features.

Transportation

The function is to reliably protect the surface of the craft. As a rule, awnings should not allow moisture, dust and dirt to pass through. The “blanket” is equipped with fastening devices, through which it is firmly fixed to the boat.

How to make a cape tent

To attach the tent to the ice, it is best to use screws, which you can also make yourself. The simplest option- weld pieces of metal rod to the long screws.

You can put rubber or silicone tubes on both sides of the rod, in this case it will not cool your hands, and it will be more convenient to hold it. Such a screw can be easily screwed into the ice and then removed back.

You can also use construction screws to secure the tent. Their advantage is that they are hollow, so they are easier to screw into the ice.

At the end of each self-tapping screw, use a needle file to sharpen 3-4 sharp teeth. It is also advisable to drill a through hole that will go into the ring.

To make the screws screw in easily, you can use a piece of metal rod that will act as a handle.

DIY frame tent for winter fishing

A more complex option is making a frame tent. The frame can be made of metal or plastic pipes, connecting them using small tubes, corner and three-way hinges. With the right approach, you will get a reliable design that can be quickly assembled and disassembled. Thus, a do-it-yourself winter fishing tent can be made of any size and shape.

A frame tent can be placed on a sleigh. In this case, it will be easy to move on the ice. To make a sled, you need to use the same metal tubes and any suitable wooden or plastic skis.

The following frame materials are used:

aluminum tubes;
steel wires with spring properties;
fiberglass rods with spring properties.

The shape of the frames is either angular or arc-shaped. The characteristic properties of springing serve to firmly stretch the awning. Aluminum frames are structural, taking into account the insertion of one part into another.

What materials are used

The main material for making awnings is synthetic fabrics, nylon-based. For the manufacture of viewing parts - window, windshield - polyethylene or lavsan is used. However, long-term use affects the quality of the review. Therefore, it is better to use polyvinyl chloride-based film.

On a note! PVC fabric itself is not used in the manufacture of awnings due to its roughness, heaviness and complete lack of air passage.

Making a dome tent

You can make a more complex pattern and make a dome tent. A do-it-yourself ice fishing tent in the shape of a dome will require more time to manufacture. It is not as compact for transportation as a cape, but it will also be much more convenient to fish in it.

An ice drill is not suitable as a support for a canopy. You need to prepare a special spacer with a pointed end that will stick into the ice. To make the tent easy to transport, the spreader must be collapsible. Its individual sections can be connected using metal tubes - this type of fastening was used in old bamboo fishing rods.

There should be holes along the edges of the dome for attaching the tent to the ice using spacers. Another option is to sew on loops.

Bow awning

In manufacturing, for reasons of safety, convenience and “dryness,” moisture-resistant materials and appropriate components that optimize the quality of water resistance will be required.

First you need to decide on the exact dimensions of the boat and, if necessary, make the corresponding drawings. In addition, to determine the fastening of the frame, it is necessary to inspect the fastening fittings located on the sides of the boat.

On a note! The first manufacturing steps are carried out by making an approximate size pattern on a “test” fabric, after which the sketch is transferred to the base material. At the same time, we must not forget about the additional allowance of fabric to form a “sleeve” for passing the fastening.

DIY winter fishing tent - making a floor

It is not necessary to make a tent floor, but it will make fishing as comfortable as possible.

Isolon (polyethylene foam), one of the types of sheet insulation, is perfect for its manufacture.

It is better to take a variety of this material with the smallest bubbles - it is very dense and conducts heat minimally.

This flooring helps retain heat. When using it, the ice under the tent does not melt even when using powerful heating devices. In addition, you can lay out everything on an isolon mat fishing equipment, which do not have to be placed in the snow.

How to make a walking awning

The organizational stages of manufacturing this type are similar to the bow one: we determine the dimensions of the boat, the frame, and make a pattern for the awning using test material.

The following materials will be required:

a pipe for an arc measuring at least 20 mm (at least 4 m);
bracket (at least 9 pcs);
awning fabric (not less than 9 m);
nylon threads;
transparent film for window parts;
fasteners for fastening parts of the awning when folding them (at least 10 pcs);
buttons for fastening the awning.

First, a frame is made: one pipe will be the supporting pipe ( big size), and the second will be mounted on the middle part of the carrier (small size).
Manufacturing occurs by bending aluminum pipes to obtain the desired shape, taking into account the dimensions of the boat and the expected ceiling height of the future awning.
Having prepared the desired shape of the arc and retreating at least 20 cm from the base of the tube, a device - a clamp, with holes for bolts - is placed in the middle of the supporting frame.
The small frame is equipped at the ends with a fastening device with a coupling to limit its rotation in one direction. With these fasteners, parts of the frame are fixed to each other with bolts. Here you need to take into account that the limiter in the fastener is on outside small frame, from the carrier.
Having previously installed the frame on the desired part of the boat, marks are made to place the fastening spots.
The parts of the boat where the marks were made are cleaned and covered with glue. In the same way, the patches are covered and glued.
The upper edges of the frames must be equipped with clamps-rails, into which rubber shock-absorber belts will be attached, equipped with hooks that will be attached to the front and rear parts of the boat cylinder in fastening fittings.
After installing and fixing the frames in a vertical position, as a rule, the entire structure of the running awning will be placed on them. After manufacturing and installing the frame, you will need to cut out the elements of the awning. They consist of several parts, including transparent oilcloth parts for front and side viewing.
In manufacturing and cutting, the lower parts of the side and front elements must have a spare length of up to 20 cm, where they will be folded to the inside, thereby forming a passage for the rope. The folded part must be equipped with holes for eyelets with a distance of up to 15 cm.
The side, viewing and overlapping parts of the awning must be stitched with zippers from the inside in order to combine with other elements of the awning and the frame.
At the end parts of the awning, where the zippers are sewn, it is necessary to attach push-button attachments to tightly fix the parts of the awning and prevent the zippers from opening when exposed to wind.
After making and cutting the awning, the first step is to attach the ceiling part of the awning to the frame arches. The top of the awning is stitched with three zippers. One zipper is sewn into inside, one on the edge of the awning and one on the outer middle part between the inner and outer zippers. Here you need to take into account how the zipper wraps around the upper arc of the frame.
The awning is pulled onto the frame by attaching the outer and inner zippers to each other, taking into account the coverage of the frame arc.
An external zipper is used to secure the viewing and side parts together.

How to sew a tent awning

An awning for an ice fishing tent can be sewn in one evening, and you don’t have to be a craftsman to do it.

Before sewing the tent, individual patterns must be fastened with pins, which are positioned perpendicular to the seam; the more of them, the better.

Transformer

The transformer is one of the most difficult to manufacture. Tubes and fasteners will be required in significant quantities. In addition, the use of special glue and a number of accessories such as hooks, eyelets, and rubber accessories is provided.

All samples and sketches of tent elements must take into account the volume of the product. The peculiarity of these awnings lies in their removable characteristics. If necessary, the entire structure can be assembled on the back of the boat, following the example of a convertible.

When making frame arches, they need to be equipped with hinges to connect them together. Also, the arcs should be attached to the side parts of the boat, taking into account the possibility of quick assembly with the awning fabric.
The production of arcs occurs by analogy with a running awning. Bends are made until the desired shape is obtained.
The front, small arc of the frame is attached to the middle of the supporting frame by means of a thrust hinge. This hinge is also a limiter in the rotation of the small frame outward from its position.
The sides of the frames must be equipped with clip-rails through which shock-absorbing belts will be pulled and attached to the side fittings of the boat. In this case, the frame will be firmly fixed in a vertical position.
After this, the cutting and cutting out of the awning elements on the basis of the installed frame begins.
By analogy with running awnings, the formation of transformers occurs by flashing the connecting parts between the elements of the awning with zippers.
The lower parts of the awnings should be sealed by folding the end of the awning in a double layer and stitching.
These parts are equipped with holes for grommets in which hooks will be placed in order to attach them to the side fittings of the boat cylinder.
After the top is located on the frame by closing the zipper, the visibility, side and rear parts of the awning are attached to it, also by means of zippers.
Having placed and attached all the parts of the awnings to each other, you need to pull them down using hooks and attach them to the side fittings of the boat cylinder.
Straps are sewn at the top to hold and secure certain elements of the awning. In fact, the difference between a transformer lies in the assembly of its elements in a separate order. If necessary, you can fold the side or front parts, securing them with a fixing belt.

Parking awning

By analogy, it is designed strictly in accordance with the dimensions of the boat. The following materials are used:

waterproof material;
masking or adhesive tape;
fastening buttons or eyelets;
scissors;
markers.

Awnings of this type are made taking into account the absence of frame arches. It is necessary to completely cover the boat with awning material;
After preliminary measuring the required part of the boat, it is necessary to cut out the awning, taking into account the separation of additional dimensions along the edges, for placing fasteners, stitching sleeves, for passing a rubber cord through them;
In the covering state on the awning, measurements are taken of such auxiliary inserts as pockets, zippers;
Next, they begin cutting on a machine;
The finished covering is stretched onto the boat;
The awning should tightly cover the entire surface of the boat, its lower parts are pulled down along the entire perimeter, and attached with sewn fastening hooks (depending on the side fittings of the boat) to the fittings of the boat.

Biminitop

Another variety is roof awnings. A distinctive feature of such awnings is the absence of side walls. The design of the awning is very simple.

Materials:

waterproof material;
transparencies;
metal arcs;
belts with buckles for shock absorption;
connecting carabiners.

First you will need to prepare support parts consisting of 4 aluminum tubes.
Counting more than 20 cm from the end, support hinges are installed on the two tubes. Similar hinges are also installed at the ends of the other two tubes.
By means of hinges, a pair of tubes is attached to tubes with hinges at part of the base. When positioned vertically, the finished structure should display the letter “U”.
Based on the width of the intended boat covering surface, metal arcs are formed taking into account their connection to the support tubes.
In order to achieve the integrity of the tubes, a rod consisting of a durable rubber material can be passed along the inside of the support tubes and the frame arc, which will be attached to the base parts of the opposite support parts.
Next, on the side parts of the boat you need to place 2 spots, with a hole for passing the bolt, and on the back and front of the boat there are 4 carabiners, into which the support tubes will be tied by tightening the shock-absorbing belts from the frame parts to the carabiners.
After the supports are installed on the spots, on top part frame, you need to tension the awning material.
On a note! When pulling the bow poles towards the stern of the boat, the front part of the awning should be pulled more tightly so that it is at a lower level than the rear bow. Through this, the aerodynamics of the structure will not be compromised.
Having made the necessary measurements of the awning in cutting it out, you need to leave an extra 15-20 cm of material at the edges for making sealing layers.
Zippers are sewn into the compacted parts of the upper element of the awning from the front and back.
Sleeves through which nylon threads will be passed, which will be attached to the arches of the frame.
One pair of zippers is sewn from the inside of the awning, and the second pair is sewn on the extreme side of the awning.
After this, the finished awning is taken and placed on the arches of the frame, taking into account the folding of the ends of the awning onto its inner part towards the zippers sewn from the inside, fastened and fixed.

Thus, the awning is installed.

Awnings depend on general form boats and their purposes. In the situation of using awnings for overnight stays, it is necessary to provide ventilation capabilities.
The dimensions of the boat and its features should be taken into account when the craft is inflated.
Tarpaulins are often used as awning materials. But, we must take into account the fact that tarpaulins become pliable over time when exposed to moisture. To prevent this, you need to treat the tarpaulin with a waterproof compound.