Homemade water vacuum cleaner for the pool. Do-it-yourself pool vacuum cleaner: manufacturing instructions. What is an underwater vacuum cleaner

If you have a swimming pool, you definitely need to clean it. Moreover, this is not affected by the quality of the installed filter. Dirt, debris, fallen leaves, hair - all this gradually accumulates on the bottom and walls of any hydraulic structure. The most profitable way would be to clean the pool with a handheld vacuum cleaner. However, if it is not possible to purchase it, there is an option to make it yourself.

What methods are used to clean swimming pools?

Besides using cleaning devices, there are many options for keeping your pool clean. The main ones include frequent replacement of water and cleaning filters. As a result, the water will contain fewer harmful microbes and its quality will be higher. However, it is quite difficult to follow these rules, because ideally you need to change the water at least twice a week, or even more. It all depends on the degree of contamination and the size of the hydraulic structure. Even the smallest pool can hold a huge amount of water, translating into numbers - up to tens of cubic meters. Therefore, changing the fluid so often is not cost-effective. It’s okay with its consumption, but what to do with the water that you drain. So if you don’t want to create a swamp with harmful microorganisms, a hand-held vacuum cleaner is the best option.

There are several other methods you can use:

There are special pumps with cleaning filters. Their work is aimed at purifying water directly. Depending on the device used, the degree of water purification will vary. This way you will kill harmful microorganisms that may live in a dirty environment.
The second effective way is to use chemicals. They also purify water at the cellular level. You won't be able to get rid of large amounts of trash this way.
You can use very simple tools: a net and a brush. However, without a suction filter, dirt will not leave the floor, but will only spread across the surface. It is good to use a net before using a hand-held vacuum cleaner to remove leaves and large debris.

Thus, cleaning the pool no longer seems as easy as it might have seemed when you purchased it.
In order to make a water vacuum cleaner for a pool with your own hands, you need to have an idea of its structure.

If we briefly and clearly describe the principle of operation of a hand-held vacuum cleaner, it boils down to the usual distillation of water and passing it through several filters. There is a main pump; it pumps water that enters the hose through the brush. It is thanks to the brush that all plaque on the walls and floor of the pool moves away from the surface and is absorbed by the filter.

Note. Depending on the level of contamination of the pool, you may need to change the cleaning filter several times. So evaluate the power of the device in advance and, if necessary, purchase additional filters.

To ensure proper pool cleaning, go over the areas where the pool is dirty several times. This way you will get more effect.

6 rules that will help you clean your pool less often:

When you are not using your pool, make it a habit to cover it.
Protect the pool from animals swimming in it. Also stick to the specific clothing you wear when swimming.
Use a net and frequently collect large debris from the pool surface.
Purchase a chemical solution that will prevent the accumulation of harmful organisms in the water.
Change the pool water at least once a week.
Remember that cleaning a dry pool has a better effect. So remove accumulated deposits from the sides of the hydraulic structure by first draining the water.

DIY vacuum cleaner

Perhaps some of you have ever thought about how to make a pool vacuum cleaner with your own hands.
The first thing we'll start with is the brush. Its main purpose is to scrape off plaque from the surface of the pool. This is an important part of the work, since the filter cannot do this on its own. There are two scenarios here. The first involves creating a brush from improvised materials, because its design is very simple and does not require special materials. Or you can purchase this device in a store. Its cost is not high, so everyone can afford it.
If you decide to start creating a brush yourself, then you need to know several options on how to do this:

The first method is to use a brush from the attachment of a home vacuum cleaner. Surely you have at least one attachment you don’t use. It can be attached to a hose. There is only one nuance - size. Cleaning with it will take you a lot of time and effort.
The second method involves using a polypropylene pipe. Take a small length, about 30 cm and cut it along the length. Divide the product into two parts and insert it into a special tee, which is used for installing plumbing at home. You can't do this without soldering. We took two adapter holes. Now take another piece of pipe and insert it into the third empty recess. All that remains is to plug the remaining pieces of pipe and voila! The brush is ready.
This method involves improving the second option. Here you need to add a couple of details, for example, a wiper blade on a car. Screw the brush onto the pipe and you're done.

Note. When working on the brush, make sure that it does not contain sharp corners. Otherwise, they may scratch the surface of the pool.

In the process of creating a bottom vacuum cleaner for a pool with your own hands, you need to ensure its tightness. To do this, take a corrugated hose and install it in the place where the water is drawn. To make the job easier, you can use either a plunger or a sewer adapter.

The final touch is to use the same polypropylene pipe as a handle for the brush.
Nothing gives a clearer picture of how to build a DIY pool vacuum than a video.

Thus, you now know how to make a vacuum cleaner for Intex pool with your own hands. There is nothing complicated about this process. All you need is a desire and some free time.

We hope the material was useful to you!

Our services:

Sewage diagrams for oil refineries. Oil refineries (refineries) belong to the industry......
DESIGN PRESTIGE LLC How to make a foundation for an extension to a house We work around the clock throughout: Moscow region, Vladimir region, ......
List of works for installing the roof of a house made of timber We work around the clock throughout: Moscow region, Vladimir, Kaluga, Tula......
Septic tank for a country house: from selection to installation We work around the clock throughout: Moscow region, Vladimir, Kaluga, Tula......
DESIGN PRESTIGE LLC Review of modern heating radiators from A to Z We work around the clock throughout: Moscow region, Vladimirs......
Modern houses and apartments are equipped with developed engineering systems that ensure comfortable living. Today people use......
Electrical work is rightfully considered one of the most difficult, since it requires not only the availability of special equipment......
A diesel burner allows you to completely switch the heating boiler to diesel fuel or make it additional view fuel really......
LLC DESIGN PRESTIGE How to make a modern bathroom design with your own hands We work around the clock throughout: Moscow region, Vladimir......
Suppliers of floorboards (Europol) in Moscow with indication of cost We work around the clock throughout: Moscow region, Vladimir......
LLC DESIGN PRESTIGE How to make a foundation for a bathhouse with your own hands We work around the clock throughout: Moscow region, Vladimir region,......
Heating water supply boiler room: How to install heating in a house Modern heating with a gas boiler Boiler room repair Tver region......
Contents: Construction of a biological treatment station Biotank Model range Advantages and disadvantages Features of operation Maintenance...... LLC DESIGN PRESTIGE Problems of building a foundation on clay, choosing the type of foundation for a house We work around the clock throughout: Moscow......
DESIGN PRESTIGE LLC List of Moscow companies supplying damper tape We work around the clock throughout: Moscow region, Vladivostok......

To keep the pond clean. Clean the water from microorganisms and make it crystal clear, but only your own hands or a vacuum cleaner will help you get rid of debris, sand at the bottom and slippery deposits on the walls!For example, if you have a small pool, you can do DIY vacuum cleaner. Instructions here.

All units for this purpose are not cheap. That's why A DIY pool vacuum cleaner is a good way out. In addition, the design of the simplest manual vacuum cleaner consists of a brush, a tube for draining water and a handle.

For a homemade vacuum cleaner you will need:

a brush from an old vacuum cleaner, a tee with plugs, or any other device convenient for cleaning the walls and bottom of the pool.
A corrugated tube or hose for drawing contaminated water from the pool into the filter. The length of the hose depends on the size of the pool.
A plastic or metal tube to make it convenient to move it along the walls and bottom of the pool.
Plunger.

ADVICE!Do not skimp on the length of the corrugated tube. The diameter of the pool should exceed its length by no more than 50 cm. A soot pipe will create inconvenience and significantly complicate the cleaning process.

Stages of connecting parts

The tee is sealed on both sides with plugs.
A narrow long hole is cut out in the middle of the tee. In the future, this part of the vacuum cleaner will play the role of a brush. A sponge can be attached to the tee as an additional cleaning agent.
A corrugated hose is attached to the tee.
The other side of the hose is attached to a plunger; it is placed in the skimmer. In principle, the homemade vacuum cleaner is ready. When the pump is turned on, water will suck debris from the bottom using a brush and corrugation. The debris will go into the skimmer, be cleaned and come out again.
But for convenience, it is advisable to attach a strong metal or plastic tube to the brush. If the brush is plastic, then it will be more convenient to solder it to the pipe with a soldering iron. If it is metal, then make an additional hole under it. But you will need rubber gaskets for sealing.

ADVICE!Sand or file all edges of the cut pipe. It is important that sharp corners do not damage the coating of the pool bowl. When gluing and soldering, use only high-quality, water-resistant materials.

Conclusion

With such simple details DIY pool vacuum cleaner is ready. A homemade vacuum cleaner is an excellent budget option for a small pool.

Cleaning the walls and bottom homemade vacuum cleaner necessary several times a week. Moreover, it carefully passes all areas of the walls and bottom of the pool, otherwise the water will quickly bloom and be unsuitable for swimming. A homemade vacuum cleaner can handle this task quite well. In addition, a handheld vacuum cleaner is very convenient for cleaning hard-to-reach places and pool walls. Some models of robotic vacuum cleaners do not have this function. And this is definitely a big plus for the little helper. For good result, the main requirement will be sufficient.

Happy owners of country pools know that this is not only a pleasant cooling bonus in the summer heat, but also a very capricious design that requires proper care.

Surface bottom And walls pool, as well as the water filling it, it is necessary regularly cleanse For these purposes, as well as to increase the service life of the equipment itself, its owners use underwater vacuum cleaner.

Remarkable the fact that a vacuum cleaner for cleaning a pool can not only be bought in a store, but also made with your own hands. This is a fun and easy process.

In this article we will talk about types underwater vacuum cleaners, their designs and operating principle. We will also give example making a vacuum cleaner for the pool with your own hands.

Types of underwater vacuum cleaners

According to their design, vacuum cleaners are three types:

Manual;
Automatic;
Semi-automatic.

Handheld vacuum cleaners

Manual models are the most simple in operation and most profitable in terms of their cost devices. Purchasing such a vacuum cleaner will be a practical solution for caring for a country pool or an artificial reservoir with a small area.

Design handheld vacuum cleaner includes the following details:

Metal telescopic rod;
High power engine;
Corrugated hose;
Cable for connecting to the electrical network;
Brush.

Remarkable that this device can be directly connected to a device that collects the top layer of pool water ( skimmer).

Choosing specific model of hand-held vacuum cleaners, all characteristics should be taken into account bowls swimming pool First of all - his depth, which must match the length telescopic device handles.

Note! Using various accessories - telescopic tubes and hoses, you can carry out complete cleaning of pools of various designs.

Semi-automatic vacuum cleaners

Semi-automatic models have more power, rather than manual ones, and differ from them in the number of their functions.

They work mainly on hydraulic traction, and their design allows you to adjust intensity water pressure, changing the flow rate if necessary.

Another submersible device used for water purification, including for a swimming pool, has a similar operating principle.

Semi-automatic designs are distinguished by the presence of a special trash bag and the ability to directly connect to the skimmer.

They good And comfortable for cleaning swimming pools with flat bottom, the surface of which has depressions.

Easy to wash the valve is also dignity semi-automatic vacuum cleaners. Thanks to the presence of this part, the surfaces of the pool, whether it is collapsible or stationary, are cleaned fast and effectively. Old sediment that has accumulated in a layer at the bottom of an artificial reservoir is also easily eliminated.

Automatic vacuum cleaners

Automatic models, more commonly referred to as robot vacuum cleaners, are recent engineering inventions.

Such a device is capable offline and work continuously for 8 hours, without any need for controlling person.

Latest computer technologies provide the ability to install certain software parameters operation of the device.

Control of such an autonomous mechanism is carried out via remote remote control.

How does a pool vacuum cleaner work?

This device is intended for cleansing surfaces of artificial reservoirs. The operating principles of each type of model are generally identical: contaminated water skipped through the built-in filter and then goes back into the pool.

Instructions for using a handheld vacuum cleaner

How to use semi-automatic and automatic models

Before you start using the vacuum cleaner, you should place into the water and connect hose with skimmer. Filtration pump will create pressure and, becoming a source of vibration, will help the device move along the surface of the pool.

Movements semi-automatic the devices are chaotic and do not have any clear, programmed scheme. It cleans not only the surface along which it moves, but also filters water.

Automatic vacuum cleaners perform the same functions as other types of models. Difference lies in the absence of the need to connect them to the water supply systems of the reservoir.

DIY water vacuum cleaner for the pool

In order to clean the pool, it is not necessary to purchase ready device. It won't be difficult to make it on one's own.

All that is required is the availability of certain materials and certain creative skills.

So, to create homemade underwater vacuum cleaner for you will be required:

Corrugated hose;
1.2 m polypropylene pipes;
Plugs;
Plunger.

The width of the hose, pipe and rubber bands depends on diameter hose from which purified water flows.

Important! You should not skimp on the hose: the diameter of the pool should exceed its length by no more than 50 cm, otherwise the quality of cleaning the reservoir may suffer.

Let's move on to creating a vacuum cleaner:

You can use a purchased one as a nozzle. brush, or - plunger or fitting, in which you will first need to make several cuts. These cuts will prevent the device from tightly suctioning to the surface of the pool. But it is best to give preference to a brush. It will help you with the pool cleaning process. most effective, and will also significantly shorten its duration. A brush for ponds is especially relevant with backlight, which require more thorough cleaning, but at the same time delicate.

Note! If the vacuum cleaner pump is equipped with a paper filter, it should be removed before starting to clean the pool, because it will not be able to retain the smallest debris located at the bottom.

Prices for purchased pool vacuum cleaners

Price underwater vacuum cleaners varies over a fairly wide range and depends, among other things, on manufacturer.

Among manual models, budget products are Bestway(the most inexpensive models are up to 3 thousand rubles).

A little more expensive and, accordingly, more functional – vacuum cleaners Pool Blaster. However, this company has models whose price exceeds tens of thousands of rubles.

Aquabot- premium vacuum cleaners. Average price of devices - from 50 thousand rubles.

And, perhaps, an option that is an excellent example of the price-quality ratio - products Intex. The price of manual models of this company starts from 3.5 - 4 thousand rubles. The Intex automatic vacuum cleaner can be purchased for 6-7 thousand rubles.

Acquainted with photo And video specific models, and at the same time get an accurate idea of their quality characteristics at official websites manufacturers.

Vacuum cleaner– a useful thing for the owner of a swimming pool or other artificial reservoir. It’s so nice to plunge into a clean, completely transparent water on a hot summer day, and in the evening - sit nearby, admiring its tints.

He talks about how to clean the bottom of a pool with a homemade vacuum cleaner. This Video:

A pool vacuum cleaner is an excellent invention for cleaning pool surfaces. Regardless of the quality of the installed inlet filter, plaque forms on the walls of the reservoir and at its bottom. In addition, dirt often gets into the pool in the form of leaves and dust, which, when deposited, creates an unpleasant layer on the surface. Such stains can be removed in many ways, but one of the best is a pool vacuum cleaner.

Pool cleaning methods

There are many ways to keep your pool clean. One of them is constant water replacement and refilling through special filters. In this case, the water will not have time to stagnate and pathogenic organisms will not be able to quickly develop in it. However, this method is very expensive, because the water will have to be changed at least 1-2 times a week... and there can be a lot of it.

Depending on the size of the pool, even if even a small frame is installed at the dacha, the amount of water can reach tens of cubic meters. Even an average pool with dimensions of 4x2 m and a depth of 1.2-1.5 m is already more than 10 cubic meters of liquid. Just calculate how huge the expense will be. But that is not all. Of course, with water from a pool that has been in it for only a few days, you can wash your car, irrigate trees, rinse even the façade of a house, or water all the beds in your garden. But how much water will it take? A cube or two? Where should the rest of the water go? Pour it down the drain?

It’s good if so, but often there is no central one. Then the water is drained into the nearest ditch, but this is fraught with many problems - from the development of harmful microorganisms there to the creation of a small swamp with frogs and snakes.

In general, this is not an option, unless you have a swimming pool at your dacha with only a cube or two, for example, an inflatable children's pool. Then, in principle, the question of cleaning it disappears. But we are talking about medium-sized structures, and therefore we need to look for the right way.

You can use a distillation pump with filters, but you must understand that it only purifies water. That is, depending on the technology and equipment used, the water will be purified from microscopic impurities and organisms that can create a pathogenic environment;
Can be used for chemicals, which will simply lead the water to a dead state. But again, you will only get rid of bacteria, but not of debris on the surface of the water and plaque on the walls of the pool;
Using a special net will help collect leaves and pieces of paper from the surface, and a brush with a long handle will help remove some of the plaque from the waterline. But the rest of the dirt will simply settle and remain at the bottom.

As you can see, cleaning a pool that is filled with water is no longer as simple a task as it was previously thought when purchasing it. Here you need to use complex methods, one of which will be a vacuum cleaner.

What is a pool vacuum cleaner?

This equipment, if you don’t go into too much detail specifications, is a pump for distillation and purification of water with several filters. From the main pump unit there is a long hose with a handle and a brush, through which dirt and plaque are collected. By wiping the bottom and walls of the pool with a brush, bristles or the rubber base of the brush, you remove dirt from the surface, which, along with the water, goes into the hose and reaches the pump, where it is cleaned by passing through a filter or several filters. Depending on the power and general purpose of the vacuum cleaner, the filters inside it can even be changed several times during one cleaning, it all depends on the severity of the contamination.

The unit helps with cleaning sediment, as well as plaque that forms along the waterline.

Most often these are gray and yellow spots, or even a film that needs to be rubbed well so that it moves away from the walls and bottom of the pool.

If you work with the equipment correctly and systematically, it can serve you for quite a long time. In addition, each individual pool cleaning will take much less time.

How is the price of a pool vacuum cleaner determined?

You can buy such equipment without any problems. Today, vacuum cleaners are available from companies offering swimming pools and complete equipment for them, as well as from many wholesalers, online stores, and even in standard retail. But the price tag may vary significantly.

At first glance, you can pay several thousand rubles for a miniature unit, but will it do the job? On the other hand, is it worth purchasing powerful equipment and reproaching yourself for such serious waste for a long time? Probably, it is necessary to determine some alternative method with the help of which it will be possible to find a solution to the issue for minimal money.

Prices for the device can reach hundreds of thousands of rubles. For example, robotic vacuum cleaners that independently move along the bottom of the bowl and clean its surface. The same powerful machines from recognized pool manufacturers, recommended, but terribly expensive. Well, and other options, which often cost more than they should.

Alternative cleaning of a small country pool

We decided to continue the theme, starting from small pools for summer cottages. Let it be inflatable or frame pools, because most often these are the ones we have installed. Today we will skip capital and composite ones, since we are absolutely sure that when purchasing a pool for a million or two, no one will bother with a device for cleaning it. The complex system will be purchased on the first day of purchasing the pool.

Let's continue about small plastic, inflatable and frame bathtubs. They need to be washed and cleaned, because heated in the sun is an excellent environment for many disease-causing pathogens. So we get rid of them in several effective ways:

Every day we cover the pool so that nothing unnecessary gets into it;
We take procedures only correctly - after a shower, in special swimwear, do not forget to take off your slippers and do not allow animals, even the most beloved ones, into the water;
We often collect debris from the surface of the water with a net or special plastic buckets;
We use it, which will help cope with bacteria, algae and other negatives in the water;
We change the water on time;
And we definitely use cleaning and washing of the dry pool while it is out of water, as well as cleaning and washing with a special vacuum cleaner.

Yes, it will take time, but there is no way around it, especially if you want the procedures to be pleasant and not negatively affect your health.

Do-it-yourself vacuum cleaner for cleaning the pool

So that you don’t have to purchase expensive equipment, we will give you advice on how to make it yourself for pennies. You will only need to spend money on high-quality filters for the pump, as well as chemicals for pools.

We decided to bypass several models where the base is created independently. We don't need to think about the design of the pump, because we already have it. But we have thought through the cleaning system to the end.

It's really simple and we'll only need to combine the pump we already have with a few extra parts.

Vacuum cleaner brush

The brush is that part of the overall surface cleaning mechanism that will remove plaque from the walls of the pool. It can be used for daily cleaning if necessary, or for tougher dirt if you clean much less frequently.

The brush can be made with your own hands from different materials, or simply purchased at the store. This is far from the most expensive piece of equipment, and therefore everyone can afford the purchase.

If you want to make a brush yourself, there are several options:

The first is that you simply connect a brush from a home vacuum cleaner to the water intake hose of the pump. Almost every modern household appliance comes with a brush that we don’t use. It has a very narrow slot, flat and small, for cleaning in corners and behind furniture. It can also be used for a swimming pool. But there is one drawback - it is really small, and due to this, cleaning time can seriously increase;
Brush made of polypropylene pipe. You need to take a pipe, which is used for distributing water in the house, cut off only 20-30 cm from it and make a cut along the pipe only 3-5 mm wide. Next, cut the pipe in half and insert both pieces into a tee, which is also used for wiring in plumbing work. Naturally, you will have to use soldering here. Now, in the third hole of the tee, install another piece of a whole polypropylene pipe, which will become an adapter between our brush and the hose leading to the pump. And the first two pieces of pipe, which have a slot, need to be plugged at the edges; there are also special plugs for this. The brush is ready!
The third type of homemade brush for a water vacuum cleaner is a modernized brush made from a plastic pipe. That is, we take a ready-made brush that we just created and add several auxiliary parts to it. This can be a rubber band from a regular car windshield wiper that is glued to a pipe with a slot. The rubber band will help remove dirt from the surface. Also, it can be a thin strip with bristles. Any addition can be glued or screwed to the pipe with small screws!

When creating a brush, you need to make all edges without sharp corners so as not to scratch or tear the surface of the pool. You also need to work only with high-quality glue and soldering for polypropylene pipes, so that with minimal force under water the brush does not fall apart. Please also note that the slot in the water intake pipe is offset, depending on the angle of the brush to the walls or bottom of the pool, and the rubber band or bristles that we installed on the brush for scraping off dirt should not get into the slot and interfere suck up dirt.

Connecting equipment

Now we need the homemade unit to work. To do this, it must be airtight, first of all.

We take a simple transparent corrugated hose, which in plumbing work is installed on siphons under sinks, and fix it to the place where water is taken from the pool. Usually it is already there, since through it the pump draws water from the distillation bowl.

Our hose can be connected quite simply, and there are several ways to do this. The first is to use a sewer adapter, choosing it exactly in size so that the elastic fits tightly to the water intake and also tightly grips the hose. And, secondly, use an ordinary plunger, in which you need to make a hole exactly in the middle, where you can install another piece of plastic pipe. Next, the plunger can be put on the water intake, and the vacuum cleaner will be ready to go!

Please note that it is much more convenient to work with rubber sewer adapters or other plumbing parts, since due to the large assortment it will be much easier for you to do right choice by size.

Another required detail is the handle. This could again be the same polypropylene pipe 1.5-2 meters long, which will be installed on the brush. With its help, you can set the entire cleaning mechanism in motion.

How a pool vacuum cleaner works (video)

Working with a homemade vacuum cleaner

When our equipment is ready, we install it and check its functionality after turning on the pump. If everything is normal and the water is sucked in, passes through the filter and is discharged back into the pool, we begin cleaning it.

It would be much more correct to start by cleaning the walls. It is advisable to immediately wash those parts that are above water, which can be done with a regular brush. Next, walk along the waterline and vertical walls in the water. And only after finishing cleaning the walls, you can move on to removing dirt from the bottom.

You will only need about an hour of time for an average pool to get it in order. Now the water will be clean and safe, naturally, subject to the integrated approach that we talked about earlier.

By spending just half a day purchasing everything you need, drawing up a drawing and the assembly itself, you will save a lot of money, and you will be able to clean your pool at any time. But if you have other thoughts about our homemade equipment, we'd love to hear them. Write to us in the comments to the article... we will be very grateful!

Arrangement of a swimming pool near the house - important condition comfortable and pleasant pastime. However, an artificial pond placed outdoors requires careful care and regular cleaning. IN open pool Dirt, dust, debris and leaves from trees are brought in. Regardless of the type and power of the installed filtration equipment, plaque forms at the bottom of the “water” bowl and on the walls.

The first option involves the use of a water vacuum cleaner, nets, brushes and filters. Physical way helps get rid of dirt particles. Some people prefer to change the water frequently instead of mechanical cleaning. But this takes a lot of time and effort, and also significantly increases water consumption. In addition, the described method is not suitable for large pools.

Important! Frequent drainage of water promotes the development of microorganisms in the ditch and the formation of a swamp in the area.

Proper organization of pool care includes a number of activities:

Using a distillation pump with filter. The device purifies water from microscopic impurities and pathogens.
The use of chemical compounds that bring water to a “dead” state. The preparations free the pool exclusively from bacteria, but do not remove debris and plaque from the walls.
Using a net, you can collect pieces of paper and leaves from the surface of the water. A long-handled brush will help remove some of the sediment from the waterline. The remaining dirt particles will settle at the bottom.

Cleaning a filled pool is not an easy task. An integrated approach to solving the issue is needed. One of effective methods The use of a special vacuum cleaner is considered.

Benefits of using a pool vacuum cleaner

A bottom vacuum cleaner sucks up contaminated water, passes it through a filter, and then throws it back into the pool. Systematic regular cleaning with such a device saves energy and time on cleaning. Key benefits include:

no need for constant water replacement;
wide range of choice - you can choose a unit of suitable power and performance;
the ability to clean the bottom, steps and walls;
ease of pool maintenance - the work can be done independently without the involvement of professional pool cleaners;
gentle cleaning of the pool bowl without the risk of damage;
saving time.

Features of different types of water vacuum cleaners

All the lineup Pool vacuum cleaners are classified into three main types:

manual;
semi-automatic (vacuum);
automatic (robot vacuum cleaners).

Manual device the simplest option, optimally suited for cleaning inflatable and frame pools of small areas. The design of a vacuum cleaner usually includes two attachments:

A brush for cleaning different areas of the bowl from mud and silt deposits. After connecting the vacuum cleaner to the garden hose, the incoming water lifts dirt from the bottom. The sediment enters the bag provided in the apparatus.
A mesh net for collecting large debris from the upper balls of water.

Contaminated water is purified using an internal filter and thrown back. At the end of the work, the accumulated debris is removed from the skimmer.

A handheld vacuum cleaner is the most budget-friendly type of such equipment. Advantages of the device: ease of use and high degree of safety. The downside is the ability to clean small pools.

Principle of operation semi-automatic vacuum cleaner. The device is immersed under water, and its hose is connected to the skimmer. The filtration pump creates vibration and pressure, which causes the vacuum cleaner to move chaotically along the bottom of the pool. Vacuum models operate on hydraulic traction and are particularly powerful.

Advice. When choosing a semi-automatic vacuum cleaner, it is necessary to take into account the parameters of the pool and the material of its coating.

Robot vacuum cleaners- a real technological breakthrough. The device independently cleans the pool without human presence. Control is carried out using the remote control. A significant advantage of the automatic unit is that it is suitable for swimming pools different sizes, shapes and surface types. However, you won’t be able to make a robotic pool vacuum cleaner with your own hands.

Do-it-yourself pool vacuum cleaner: manufacturing instructions

Creating a water vacuum cleaner for a pool with your own hands is within the power of anyone and will only take a little time. All necessary materials for its manufacture can be purchased at any plumbing store:

polypropylene pipe;
sealing rubber bands;
corrugated hose;
a brush or other element that will serve as an intake nozzle.

When describing the process, it is assumed that a conventional pump is already available. The choice of diameter of the hose, pipe and sealing rubber depends on the size of the filtered water supply pipe.

Advice. You should not skimp on the length of the corrugated hose, otherwise cleaning the pool will be inconvenient.

Making a Pool Cleaning Brush

Let's consider several options for making an intake nozzle.

Method 1. Connecting a regular brush from a household vacuum cleaner to the water intake hose. It is better to choose a brush designed for cleaning furniture - it is small, flat, with a narrow slot.

Method 2. Making a cleaning brush from a polypropylene pipe. For work you will need: a tee, a plastic pipe, plugs, a grinder and a soldering iron. The procedure for assembling a homemade brush:

Cut 25-30 cm from the pipe.
Make one cut along the resulting cut, about 3-5 mm wide.
Cut the pipe in half and insert both pieces into a polypropylene tee used in plumbing work for wiring.
Install a piece of polypropylene pipe into the third hole of the connecting tee. It is this segment that will serve as an adapter between the pump hose and the brush.
Seal the sections of the first pipe (with slots) at the edges with plumbing plugs. The homemade brush is ready for installation.

Method 3. The brush made according to the second option can be slightly modernized. It is enough to attach a narrow bristly strip or rubber band from car wipers to a pipe with a slot. A minor improvement will increase the cleaning efficiency. The proposed parts can be replaced with foam rubber cuts or other elements - it’s just a matter of creative ingenuity and ingenuity.

Advice. The edges of the cut pipe must be processed with a file or emery so that the sharp corners do not scratch or damage the coating of the pool bowl. For soldering and gluing, it is advisable to use high-quality waterproof materials.

Connecting a homemade vacuum cleaner for a pool with your own hands

The next step is connecting the brush. For normal operation of the water vacuum cleaner, the main condition must be met - the tightness of the connections of all parts.

You will need a transparent corrugated hose installed on siphons under sinks and sinks. Fix the corrugation at the place where water is taken from the pool. The connection is made using a sewer adapter of suitable size. The rubber band should fit tightly around the hose and fit against the water intake.

An essential part of a water vacuum cleaner is the handle. Its function can be performed by a polypropylene pipe about two meters long (depending on the height of the person and the dimensions of the pool).

Vacuum cleaner for frame pool ready with your own hands. The homemade device is suitable for cleaning other types of small pools (inflatable, plastic bowls, etc.).

To reduce the waste of water, it can be passed through a filter and then fed back into the reservoir. A filter must be installed at the end of the hose connected to the outlet or replaced with another trapping device. Plumbing stores sell many special filter bags that hold large and small particles of dirt, but allow water to flow through.

Advice. The water in the pool should not stagnate. Therefore, it is more advisable to fill the bowl with new water. However, to reduce consumption, pool cleaning with water replacement can be alternated with cleaning without replacement.

Do-it-yourself bottom vacuum cleaner for a pool using improvised means

Let's take a closer look at how to make a pool vacuum cleaner with your own hands using a regular plunger.

Necessary materials:

corrugated hose - 2 m;
polypropylene pipe - 1.2 m;
plunger;
plugs - 2 pcs;
tee.

Work order:

Make a tee from a polypropylene pipe, like on a vacuum cleaner. Connect and solder the pipe sections. To heat up, you can use a soldering iron or a gas torch.
Place plugs on the ends of the pipes.
Cut a longitudinal hole at the bottom of the pipe. Sand the edges with sandpaper or a file.
Solder a handle to the top of the nozzle.
Make a through hole in the middle of the plunger into which to insert a thick pipe.
Connect the plunger through the pipe to a corrugated transparent hose.
Connect a homemade vacuum cleaner to the inlet valve of the pool filter pump. Debris collected from the bottom will remain in the filter, which can then be easily washed.

Cleaning a pool with a homemade vacuum cleaner: video

Alternative pool cleaning

Pool water heated under the rays of the sun is an excellent breeding ground for most disease-causing pathogens. Therefore, regular cleaning of the bowl is the main condition for not only pleasant, but also safe bathing.

Here are some effective ways to care for inflatable, frame and plastic pools:

Safety precautions when using a water vacuum cleaner

Cleaning the pool with a manual or vacuum vacuum cleaner for the pool with your own hands must be carried out in compliance with a number of safety requirements:

turning on the vacuum cleaner is allowed only when there are no people in the pool;
equipment connection is carried out through an RCD, in accordance with all norms and rules for working with electrical devices;
a damaged electrical cable must be replaced immediately, and the work should be entrusted to a qualified technician.

Do-it-yourself manual pool vacuum cleaner repair

Some malfunctions in the operation of a “water” vacuum cleaner can be corrected yourself. The solution to the issue depends on the cause of the failure:

The vacuum cleaner has stopped drawing water. Main causes of malfunction:
- drive repair, pulley, driving guides are littered or poorly adjusted;
- The power supply is not plugged into the outlet.
The robot vacuum cleaner draws in water, but does not move:
- the power cord is tangled or the drive belt is dirty;
- auxiliary motors do not work - specialists can solve the problem.
The vacuum cleaner does not clean the pool surface well. The most common reason is that accumulated debris is preventing the outlet valve from closing/opening.
The robot vacuum cleaner leaves some areas of the pool uncleaned. The following measures should be taken:
- rinse the filter bag;
- check the cable - it should be untangled;
- consult a service center specialist.

Vacuuming inflatable pool: video